Header
Body
Facebook IconTwitter IconYouTube IconInstagram IconLinkedIn Icon|      Where to Buy
Installation Guide
10-Jan-19

Allison 1000 C3 Torqkit (11-On) Installation | RTK-1023

Allison 1000 C3 Torqkit (11-On) Installation | RTK-1023

Part No: RTK-1023Components:5 pcs GPZ195 Friction Plates (0.071”)5 pcs 511642 Steel Reaction Plates (0.098”)1 pc 511003 P1 Ring Gear SpacerInstallation Instructions1. Install the P1 ring gear spacer 511003 between the P1 planet carrier and P1 thrust washer.2. Install C3 piston with orifice at 12 o’clock position. Lube seal surface and install evenly.3. Install in the following order (*TIP: Remove or do not install Piston Return Springs at this time):0.098” 511642 Steel Reaction Plate0.071” GPZ195 Friction Plate0.098” 511642 Steel Reaction Plate0.071” GPZ195 Friction Plate0.098” 511642 Steel Reaction Plate0.071” GPZ195 Friction Plate0.098” 511642 Steel Reaction Plate0.071” GPZ195 Friction Plate0.098” 511642 Steel Reaction Plate0.071” GPZ195 Friction PlateOE Backing PlateSnap Ring3. Check clutch clearance between C3 backing plate and top friction plate using a feeler gauge. *Recommended clearance range is 0.040”-0.060”.4. Remove friction and steel components and saturate friction plates in either manufacturerspecified ATF or comparable synthetic ATF.5. Confirm C3 piston orifice is located at the 12 o’clock position.6. *If removed in step 2, install piston return spring assembly.7. Install 0.098” steel reaction plate with slot centered over C3 piston orifice.8. Using the steel slots as a guide, align the friction plate slots during assembly.9. Align slots in steel reaction plates, ensuring slots do not block or partially block the C3 piston orifice. Note: You may need to index or flip the steel reaction plate over to accurately locate and center the slot at 12 o’clock.*TIP: If end of steel reaction plate slot lines up with last spline, plate slot will be aligned at 12 o’clock.)*TIP: One method of keeping slots aligned is to stack the parts on the P1 planet ring gear/C3 clutch hub, and load into case as an assembly in the horizontal position.a. Begin with a friction plate and index so the slot is at 12 o’clock.b. Place a steel reaction plate with slot at 12 o’clock, and alternate until 5 friction plates and 4 steel reaction plates are on/over the P1 ring gear/C3 clutch hub.c. Place the ring gear and clutch pack into the housing as an assembly, carefully aligning the steel plates to the case and keeping the 12 o’clock reference point in position.10. Install the C3 backing plate and snap ring.

Search by Transmission
Renault / Peugeot
Saturn

Featured Products

LT1000, LT2000 C3 GPZ Torqkit Clutch Pack
Part No.
RTK-1023
View
LT1000, LT2000 C1 GPZ Torqkit Clutch Pack
Part No.
RTK-1001
View
LT1000, LT2000 C2 GPZ Torqkit Clutch Pack
Part No.
RTK-1002
View
LT1000, LT2000 C4 GPZ Torqkit Clutch Pack
Part No.
RTK-1024
View
LT1000, LT2000 C3 GPZ Torqkit Clutch Pack
Part No.
RTK-1033
View
LT1000, LT2000 C4 GPZ Torqkit Clutch Pack
Part No.
RTK-1043
View
LT1000, LT2000 C3 GPZ Torqkit Clutch Pack
Part No.
RTK-1013
View
LT1000, LT2000 GPZ Torqkit Clutch Pack
Part No.
RCPTK-1001
View
Allison 1000 Transmission Torqkit Performance Rebuild Kit 99-05
1999-2005
Torqkit Performance Transmission Super Rebuild Kit
Part No.
RSKMAX-110
View
Allison 1000 Transmission Torqkit Performance Rebuild Kit 06-10
2006-2010
Torqkit Performance Transmission Super Rebuild Kit
Part No.
RSKMAX-111
View
Allison 1000 Transmission Torqkit Performance Rebuild Kit 11-ON
2011-ON
Torqkit Performance Transmission Super Rebuild Kit
Part No.
RSKMAX-112
View
4L80E Transmission MaxPak Performance Rebuild Kit 97-ON
1997-ON
MaxPak Performance Transmission Super Rebuild Kit
Part No.
RSKMAX-075
View

Where to Buy